Wavepad sound editor is a powerful audio editing software available from www.nch.com.au.
Working in Batches
Wavepad can process files in large batches. Go to Tools > Batch Convert Files. Add files using either the Add Files button or the Add Folder button. If you add one folder, a list of audio files in that folder appears, if you add a number of folders, just a list of folders appear. Click on Next. Under Command List select ADD and add a suitable effect or effects. For every effect you add, change the settings. For example, if you add ‘Insert silence at the start’, the default setting is for ‘0’ seconds, change it to ‘5’ or ‘2’ as per your convenience. Some effect changes, like pitch change, are handled with percentage values. If you put on a lot of effects, then it makes sense to save the commands list as a batch script file just in case something goes wrong. Click on Save As and enter a file name. Click on Next. Under Output File Format specify a different format or use the same format that the file was loaded in. The Output Folder has two options, to replace the files in the same folder, or to save in a different folder. Pick one of these options and click Finish.
Using WavePad As A Transcoder
You can transcode MP3 files to a lower bitrate for use in your mobile phones or PMPs to save memory space. This technique can also be used to send audio files over e-mail. First save all the MP3 files you want to work with in one folder, then go to Tools > Batch Convert Files and add files using the Add Folder Option. Click on Next, ignore the commands window and click on Next again. Under Output File Format click on Format Options. Change the Constant Bit Rate drop down box to 96 Kbps, and uncheck ‘high quality encoding’. Click OK, select an output folder and click Finish.
Advanced Noise Reduction
For high quality audio recordings, it is essential to reduce noise for clarity. There are two automatic noise reduction options available, but wavepad also allows a manual approach. Select a section of the audio file that has only noise, the larger this selection, the better the noise reduction will be. Once the selection is made, go to Effects > Noise Reduction > Grab Noise Sample From Selected Area. Then go to Effects > Noise Reduction > Apply Spectral Subtraction Based On Noise Sample.
Record Audio
Make sure a microphone or an AUX wire is providing input to your computer. Then go to Control > Record. Select a sample rate—a sample rate is the number of permanent records made from the signal per second, the default is 44100 hz, which is the same quality of an audio CD. The higher the sample rate, the higher the quality, and the more the disk space used to store the media. Click on the Stereo radio button and click on OK. A bar showing audio activity should appear. If more than one audio input device is connected to the computer, select the relevant input device in the device drop down box. If you want wavepad to start recording automatically every time noise is detected, click on Advanced Recording Options and check Auto start recording. Press the circular red button to start recording.
Text To speech
Go to Tools > Text To Speech, select a sample rate if prompted, and then type text out in the window and click on OK. Wavepad uses Microsoft’s text to speech engine, so this feature will not work if you do not have this engine. Every time this is done, a new file with the speech is created. The default is the Microsoft Sam voice, but a few alternatives are available for download from the NCH Web site.
Tone Generator
Go to Tools > Tone Generator, which is an install-on-demand module for wavepad. It is a small file, but you will need an Internet connection for this to work. The tone generator has a number of options and can generate sine, triangle, square, sawtooth and impulse train tones. Go to Tone > Number Of Tones to change the value from 1 to 16 for the number of parallel tones generated. It is possible to change the frequency of all these tones. Additionally, the tone generator also generates white noise and pink noise. Go to File > Save As WAV to save the tone for later use. Clicking on Edit will open the tone as a temporary file immediately in wavepad for you to edit.
Remove Clicks And Pops
Many recorded tracks have clicks and pops as artefacts of faulty audio hardware—or when the equipment is moved, handled or toggled. Wavepad can automatically take care of these clicks and pops. Go to Tools > Auto Click/Pop Restoration. Maximum click length is the length of the longest defect in the track—the poorer the recording quality, the longer will this be. The default is 450, which should take care of the problem. If the clicks and pops persist, increase it to 600 and run the operation again. If there are still clicks and pops after this, identify the artefact in the waveform, select it and then either press the delete key or go to Tools > Manual Click/Pop Repair.
Frequency Analysis
Wavepad offers two kinds of frequency analysis. The basic frequency analysis plots the waveform into its frequency components. For stereo files, there is a blue graph (left channel) and a red graph (right channel). Select a portion of the file, go to Tools > Frequency Analysis. You can zoom in or zoom out in the frequency analysis window to more closely look at the waveform. An alternate mode of frequency analysis offered by wavepad is Temporal Frequency Analysis, under Tools > Temporal Frequency Analysis. The intensity of any frequency at any point of time is mapped on this graph, giving a hot to cold gradient that can be analysed. A slider adjusts the heat of any particular frequency, which is useful for high intensity music. The brighter areas mean greater intensity (more decibels) of a particular frequency, and the darker areas show a lack of intensity at particular frequencies. This window also has a zoom function, and a grid toggle for reference.